Monday, June 29, 2015

Leds Keypad Switch

by J.B. Wylzan


Project 18:  Leds Keypad Switch

This project  turns On and Off  4 leds using a Membrane Switch Keypad.




4X3 Matrix Keypad Configuration:  

   ROW1 - Arduino pin 4
   ROW2 - Arduino pin 5
   ROW3 - Arduino pin 6
   ROW4 - Arduino pin 7
   COL1 - Arduino pin 8
   COL2 - Arduino pin 9
   COL3 - Arduino pin 10

*Note: These rows and columns can be changed anytime.


Block Diagram:



Hardware:
1 Keypad; 4x3 Matrix 
4 leds
4 resistors
connecting wires
breadboard
Arduino R3 UNO board

Code # 18:
/*
  iHacklab Leds Switch Keypad
  powered by Arduino
  modified by Lawsinium

Note: Keypad Library for Arduino
Authored by  Mark Stanley, Alexander Brevig
Downloaded from http://playground.arduino.cc/Code/Keypad

  Turns On and Off leds using a keypad
  The example code is public domain.
 */

#include <Keypad.h>

const byte ROWS = 4;       // Keypad has four rows
const byte COLS = 3;        // Keypad has three columns
char key = 0;                       // Initializes a variable

// Define the Keymap
char keys[ROWS][COLS] = {
  {'1','2','3'},
  {'4','5','6'},
  {'7','8','9'},
  {'*','0','#'}
};

// Connect keypad’s pins to Arduino pins.
byte rowPins[ROWS] = { 4, 5, 6, 7 };  
byte colPins[COLS] = { 8, 9, 10 };   

// Keypad syntax
Keypad keypad = Keypad( makeKeymap(keys), rowPins, colPins, ROWS, COLS );

//setup the pins' inputs and outputs void setup() {
  pinMode(4, INPUT);
 pinMode(5, INPUT);
 pinMode(6, INPUT);
  pinMode(7, INPUT);
   pinMode(8, INPUT);
    pinMode(9, INPUT);
     pinMode(10, INPUT);
      pinMode(2, OUTPUT);
       pinMode(3, OUTPUT);
       pinMode(11, OUTPUT);
       pinMode(12, OUTPUT);
}

void loop()
{
  key = keypad.getKey();     // get key
  pressKey('1', '2', 2);          // On = '1', Off = '2', pin = 2
  pressKey('3', '4', 3);          // On = '1', Off = '2', pin = 3
  pressKey('5', '6', 11);        // On = '1', Off = '2', pin = 11
  pressKey('7', '8', 12);        // On = '1', Off = '2', pin = 12                          
}
unsigned int pressKey(char on, char off, int output) {
  if(key) {
    if (key == on) {
      digitalWrite(output, HIGH);
    }
    if (key == off) {
      digitalWrite(output, LOW);
    }
  } 
}
// end of the sketch


Challenge: Use Keypad to light an LED using a numerical password. If the password is invalid a red led lights up. If the password is valid, a green led lights up.


Actual Layout:


Procedure:
1. Build the prototype as shown above
2. Run the Arduino Interface
3. Select File > New
4. Copy Code #18 above
5. Paste Code #18
6. Click File > Save
7. Click Verify
8. Click Upload
9. Press any key to turn On and Off an Led.


Project # 19:  Keypad with Password


Disclaimer:  We shall not be liable for any loss or damage of whatever nature - direct, indirect, consequential, or otherwise - which may arise as a result of your use of any information on this website. However, if you are interested in using any of the projects for personal or educational purposes, please inform the author by email. 

Public Domain Notice: Copyright (c) 2000. All rights reserved. This article is part of a book entitled iHackRobot. Copies are welcome to be shared or distributed publicly as long proper citations are observed. Please cite as follows: A Journal of a Creative Mind, Joey Lawsin, 1988, USA.


"The Last Human on Earth will no longer be Human." ~ Joey Lawsin
================================================================== 
The Homotronics® and Homodruinos® logos are registered trademarks.
Copyright Biotronics© Inc. iHackRobot®. All Rights Reserved.
Patent Pending. 2000 © ®


 ================================================================== 

No comments:

Post a Comment